For green environment


    제품 > 공정 측정 > 필터 손상 탐지

    Products > Process Monitoring > Filter Leak Detection

    (NEW) SINTROL SNIFTER A2   

 

손상된 백 탐지용 먼지 측정기

Snifter A2는 진화된 필터 손상 탐지기입니다. 이 먼지 계측기는 백하우스의 동작을 감시하고 먼지 레벨이 증가할 때 작업자에 알리기 위해 이용될 수 있습니다. Snifter A2USBRS485를 통해 신트롤 네트워크 연결을 지원합니다. 모든 파라미터와 설정들은 적절한 사용자 응용 필요에 맞추어 설정됩니다. 이 장치는 신트롤 DustTool 프로그램과 완전히 호환됩니다.

자동 설정 기능은 쉽고 빠르고  연결하기 쉬운 두 개의 독립적인 알람 신호를 발생시킵니다.

 

EX 모델들 (IECEx and ATEX) 가능

무선 RF 통신 가능

 Dust monitor for broken bag detection

Snifter A2 is an advanced filter leak detector. This dust monitor can be used to monitor the operation of a baghouse and alarm the operator when dust levels increase. Snifter A2 supports Sintrol Network connectivity over USB and RS485 interfaces by default. All parameters and settings are user selectable to best suit custom application needs. This device is fully compatible with Sintrol DustTool software.

Auto setup function makes commissioning easy and quick and two independent alarm signals enable easy connectivity.

EX models (IECEx and ATEX) available.
Wireless RF communication available.

 

     

 

 

Snifter A2
Measurement Objects  Solid particles in a gas flow
Particle Size  0.3 µm or larger
Measurement Range  From 0.1 mg/m³
Measurement Principle  Inductive Electrification
Protection Category  IP65
Sensor Length (total/measuring)  250 mm /185 mm  ı 9.8" / 7.3"
Power Supply   12-24 VDC
Power Consumption  3 W
Cable Connection  2 meter cable, 10 wires
 6.5 ft cable, 10 wires
Process Connection  - NPT 1/2 " male thread
 - NPT 1/2 " female thread welding socket (optional)
Output Signal   - Two output signals (100 - 280 mA) depending on operation  temperature
Communication Interface  - Serial communication RS-485
 - USB communication
 - Radio frequency (RF) communication (optional)
Communication Protocol  - Modbus RTU, (RS-485)
 - SNT network, (USB, RF, RS-485)
Alarm settings  - Automatic
      Alert: 5 x normal dust level
      Alarm: 20 x normal dust level
- User selectable ranges
Signal Damping time  - Fixed at factory: 10 s
 - Adjustable from 0 - 5400 s

 

 
Process Conditions
Temperature  Max 250 °C  ı  Max 482 °F 
Pressure  Max 200 kPa
Gas Velocity  Min 3 m/s   ı  Min 9.8 ft/s
Humidity  Max 95% RH (non-condensing)

 

 
Ambient Conditions
Temperature  -20 ... +40 °C (operating temp. -40 to +60 °C) 
 -4 to +104 °F (operating temp. -40 to +140 °F) 
Humidity  Max 95 % RH (non-condensing)

 

 
Materials and Weight
Probe (wetted part)  Stainless steel (AISI 316L)
Process Connection (wetted part)   Stainless steel (AISI 316L)
Enclosure  Aluminum
Probe Insulation (wetted part)  PEEK
Weight  0.7 kg  ı  1.5 lb

 

 

Top   


    제품 > 공정 측정 > 필터 손상 탐지

    Products > Process Monitoring > Filter Leak Detection

    (NEW) SINTROL SNIFTER A1+

 

손상된 백 탐지용 먼지 측정기

Snifter A1+ 는 저렴하고 사용하기 쉬운 필터 손상 탐지기입니다. 이 필터 손상 탐지기는 Snifter A1의 직접적인 대체품입니다. Snifter A1+ 는 손상부분의 빠른 확인을 하게하는 백하우스에서의 모니터링 배출구를 위해 사용될 수 있습니다. 장치의 동작은 설치 10분 이내에 보통 먼지 집약도를 확인하는 편리한 자동 설정 기능으로 쉽습니다.

Snifter A1+ 먼지 모니터는 손상과 여과능력이 약화되는 정보를 공장 작업자에게 전달하는 두 개의 프리셋 알람 경고 신호를 가지고 있습니다.

EX 모델들 (IECEx and ATEX) 가능

Dust monitor for broken bag detection

Snifter A1+ is a low-cost easy to use filter leak detector. This filter leak detector is a direct replacement for the Snifter A1 device. Snifter A1+ can be used for monitoring outlets in a baghouse enabling fast identification of leaking compartments. Commissioning of the device is easy with the convenient auto setup function which identifies normal dust concentration within ten minutes of installation.

The Snifter A1+ dust monitor has two pre-set alarm limits for alarm and alert signals to give plant operators information on leaks and deteriorated filtration performance.

EX models (IECEx and ATEX) available.

 

     

 

 

Snifter A1+
 Measurement Objects  Solid particles in a gas flow  
 Particle Size  0.3 µm or larger
 Measurement Range   From 0.1 mg/m³
 Measurement Principle  Inductive Electrification
 Protection Category  IP65
 Sensor Length  (total/measuring)  250 mm / 185 mm  ı   9.8" / 7.3"
 Power Supply  12 - 24 VDC
 Power Consumption  3 W
 Cable Connection   2 meter cable, 5 wires
 6.5 ft cable, 5 wires
 Process Connection  - NPT 1/2 " male thread
 - NPT 1/2 " female thread welding socket (optional)
 Output Signals  Two output signals (100 - 280mA)  depending on operation temperature
 Alarm Settings  Automatic
 - Alert: 5 x normal dust level
 - Alarm: 20 x normal dust level
 Signal Damping Time  Default at factory: 10 s

 

 

Process Conditions
 Temperature  Max 250 °C   ı   Max 482 °F
 Pressure   Max 200 kPa
 Gas Velocity  Min 3 m/s   ı   Min 9.8 ft/s
 Humidity  Max 95 % RH (non-condensing)

 

 

Ambient Conditions
 Star Up Temperature  -20 to +40 °C (operating temp. -40 to +60 °C)
-4 to +104 °F (operating temp. -40 to +140 °F)
 Humidity Max 95 % RH (non-condensing)

 

 

Materials and Weight
 Probe (wetted part)   Stainless steel (AISI 316L)
 Process Connection (wetted  part)  Stainless steel (AISI 316L)
 Probe Insulation (wetted part)  PEEK
 Enclosure  Aluminum
 Weight  0.7 kg  ı  1.5 lb

 

 

Top   


    제품 > 공정 측정 > 필터 손상 탐지

    Products>Process Monitoring>Filter Leak Detection

    SINTROL S301

 

 

필터 손상 탐지용 On/Off 스위치

두 개의 독립적인 알람 릴레이들로, S301은 최종 사용자가 백 손상과 전기 유도 측정원리를 사용한 필터의 약화를 확인할 수 있도록 하게하고, 먼지 모니터는 30분 이내로 설치하고 쉽게 설정을 할 수 있으며 공장 작업자에게 필터 시스템의 파손을 신속하게 알릴 수 있습니다.

신트롤 먼지 측정기는 최종 사용자가 그들에게 필요에 맞도록 수동으로 경고와 알람 수준을 조절하게 합니다.

On/Off Switch for filter leak detection

With two independent alarm relays, Sintrol's S301 allows the end user to identify bag leaks and deterioration of filters.  Using our electric induction measurement principle, the dust monitor can be easily set up within 30 minutes of installation and gives plant operators quick notification of breaches in the filtration system.

Sintrol dust monitor allows end users to manually adjust alert and alarm level signals to tailor to their end needs.  Different probe lengths and coatings give flexibility to meet a variety of applications.

 

     

 

 

S300 Series dust monitors
Measurement Objects Solid particles in gas flow
Particle Size 0.3µm or larger
Measurement Range From 0.1mg/m³ 
Measurement Principle Inductive Electrification
Protection Category IP65
Probe Length (total/measuring) 500mm/440mm, 750mm/690mm (optional),1000mm/940mm (optional), >1000mm on request
19.7" / 17.3", 29.5" / 27.2", 39.4" / 37.0" (optional), > 39.4" on request
Power Supply 115 VAC, 230 VAC or 24 VDC
Power Consumption DC model Max 3 W, AC model Max 8 W
Wiring Connections - Power Supply DIN PG11 cable gland
Wiring Connections - Output Signals DIN PG11 cable gland
Process Connection socket (38 mm OD), quick clamp (optional), flange (optional)
Output Signals - Two SPDT relays: 5A, 24V AC/DC
Range Set Up - Normal measuring range: automatic, based on average measured dust flow during setup procedure
- Extended measuring range: User selectable
Relay Alarm Settings - Automatic, set at factory: Based on average measured dust flow
- User selectable ranges
Offset Trim Automatic drift compensation
Signal Damping Time 0-300 s
Relay Delay Time 0-180 s

 

 
Process Conditions
Temperature Max 300°C, Max 700°C (optional)
Max 572 °F, Max 1292 °F (optional)
Pressure Max 200 kPa, Max 600 kPa (optional)
Max 43.5 PSI, Max 87 PSI (optional)
Gas Velocity Min 4m/s   ı   Min 13.1 ft/s
Humidity Max 95% RH (non-condensing)

 

 
Ambient Conditions
Temperature -20....+45°C and 60°C for 24 VDC
-4 to 113 °F and to 140 °F for 24 VDC
Humidity Max 95% RH (non-condensing)
Vibration Max 5 m/s²   ı   Max 16.4 ft/s2

 

 
Materials
Probe (wetted part) Stainless steel (AISI 316L)
Probe Coating (wetted part) PTFE Teflon (optional)
Process Connection (wetted part) Stainless steel (AISI 316L)
Probe Insulation  (wetted part) PEEK
Probe Sealing (wetted part) FPM Viton
Enclosure Aluminum alloy
Weight 2.3kg   ı   5.1 lb

 

 

Top